Top 10 usual forklift crashes ， forklift procedure need to take notice of these issues ！.

Do not take too lightly the forklift at the office. If the procedure is bad, there will certainly be serious accidents in minutes, and there are numerous mishaps including forklifts.

Situation 1: The forklift cargo blocked the motorist's sight, and the person in front could not be found, resulting in a rolling accident.
Case 2: In order to maintain the balance of the forklift when raising hefty items, the staff members utilized their body weight as the weight, which nearly triggered casualties.
Situation 3: The width of the forklift cargo goes beyond the allowed size of the path and hangs on the roadside shelf, which virtually creates an mishap.
Situation 4: Forklift is speeding and rolls over throughout a turn.
Situation 5: The forklift chauffeur did not discover the pedestrian, and the pedestrian did not notice the forklift.
Instance 6: The forklift raises the workers illegally, the forklift vehicle driver does not put on the seat belt, the forklift lifter falls and the vehicle driver is crushed when the forklift rolls over.
Instance 7: The forklift motorist did not wear a safety belt and dropped from the car when it surrendered and was squashed.
Forklift operation need to focus on these matters ：.

Start.
1. Before beginning, observe the environments, and after verifying that there are no obstacles that prevent the security of driving, beep the horn initially and then begin.
2. For cars with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge must be secure before beginning.
3. When the forklift starts with a tons, the chauffeur needs to first validate that the load is secure and reputable.
4. The begin must be slow-moving and steady.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground must be maintained 300mm-400mm, and the mast must be tilted backwards. .
2. Do not raise the fork too high when driving. When going into and leaving the work site or while driving, take care that there will certainly be no challenges overhead. When the load is traveling, the fork needs to not be raised too expensive, which will certainly affect the stability of the forklift. .
3. After discharging, the fork needs to be lowered to the typical driving placement prior to driving. .
4. When turning, if there are pedestrians or automobiles close by, the driving signal should be issued first. High-speed doglegs are banned. High-speed sharp turns will trigger the automobile to shed side security and tip over. .
5. When the forklift is downhill, it is strictly prohibited to shut off the fire and slide, and it is restricted to brake suddenly while driving with loads unless there are special scenarios.
6. When the forklift is running, it has to comply with the traffic rules in the factory and should keep a certain security distance from the automobile ahead. .
7. When the forklift is running, the tons needs to remain in the most affordable setting that does not impede the driving, and the gantry must be appropriately slanted back. The tons shall not be raised except when piling or filling. .
8. The elevation of the lots need to not obstruct the motorist's sight. In special situations, when the item affects the forward vision, drive at a reduced rate when turning around.
9. It is prohibited to switch on the ramp, nor to drive across the ramp. .
10. The secure driving rate of the forklift in the factory area is 5 km/h, and it must drive securely at a reduced speed when entering the manufacturing workshop location. .
11. When the forklift is lifted, lifted or driven, it is restricted for employees to base on the fork to hold items and play a balancing duty. .
12. If issues are found, they will certainly be fixed and reported in a timely manner, and they will certainly never operate with ailments or hide them.

loading and dumping.
1. When fork-loading products, the distance in between the two forks should be readjusted as needed to make the load of both forks balanced and not manipulated, and one side of the product need to be against the shelf. .
2. It is prohibited to work with a solitary fork or utilize a fork top or draw. In special circumstances, safety and security warning signs have to be set up to advise surrounding pedestrians. .
3. In the process of filling and discharging items, the forklift needs to be braked with the brake. .
4. The rate of the vehicle must be slow and constant. Be careful not to roll the wheels on the dunnage, so as not to extend the rolled objects and harm individuals. .
5. When utilizing a fork to fork the goods, the fork needs to be as deep as possible under the lots, and it should be kept in mind that the fork tip must not touch various other goods or items. The load ought to be maintained with very little back tilt of the gantry to make sure that the load does not move in reverse. The mast can be tilted onward slightly when the tons is reduced to permit easy positioning of the lots and removal of the forks. .
6. It is forbidden to fork products at broadband and collide with hard items with the fork head. .
7. When the forklift is functioning, it is restricted for people to stand around the fork, so as to prevent the collapse of the goods and injure individuals. .
8. Overloading is restricted, and it is forbidden to make use of forks to raise personnel to engage in high-altitude operations to prevent high-altitude dropping crashes. .
9. It is not permitted to use the brake inertia to slip, put, round or roll objects. .
10. It is not enabled to utilize forks to choose, transform pallet dump.

Leaving .
1. It is restricted to leave the forklift when the things on the fork impend. Prior to leaving the forklift, you must unload the goods or lower the fork frame.
2. Pull the parking brake deal Stand-on Electric Pallet Stacker with to dead or depress the parking brake switch.
3. The engine is turned off and the power is cut off. (Except for special circumstances, such as the driver does not leave the vehicle's line of sight and does not exceed 1 min).
4. Get rid of the trick. .

Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the appearance ought to be checked, and fuel, lubricating oil and air conditioning water need to be included.
2. Inspect the security performance of beginning, running and stopping.
3. Inspect whether the lights and horn signals are total and effective.
4. Throughout the procedure of the forklift, inspect whether the pressure and temperature are regular.
5. After the forklift is running, the outside leakage should additionally be inspected and the seals ought to be replaced in time.

Forklift Safety Operation Specifications.
1. You have to inspect before leaving the car;.
2. When you encounter a person in front of you during driving, you need to send a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not surpass 5 km/h;.
4. When driving, the low point of the freight ought to be 0.3 Electric Forklift Truck for Warehouse m ~ 0.4 m in the air;.
5. The transforming ought to not be also sharp to avoid the tendency of " cost-free turning";.
6. Adding and down the slope should be slow-moving and uniform, and no activating the slope is permitted.
7. Do not drive across the slope. When the slope is greater than 10%, the lorry ought to be driven in reverse when declining;.
8. When the forklift employees bring the goods and move on, if they experience huge or heavy items and go to the vehicle driver's line of sight, they need to take the reversing workout
.
The "Eight Prohibitions" should be complied with in the procedure.
1. Single fork procedure is not permitted.
2. It is not allowed to raise the goods for long distance driving.
3. It is not enabled to grab the goods by turning over the pallet with the fork.
4. It is not enabled to straight shovel chemicals, flammables and other harmful chemicals with forks.
5. It is not permitted to use inertia pressure to grab the goods.
6. It is not allowed to utilize stopping pressure to exile round or easy-to-roll items.
7. It is not permitted to bring individuals to deal with the pallet or fork, and it is purely restricted to stand under the fork after the fork is raised.
8. Do not drive laterally on slopes
.
Car park is not permitted under the following conditions.
1. Curves, slim roadways, train crossings;.
2. Areas with a longitudinal slope higher than 5%.
3. When there is an challenge on one side of the roadway, the contrary side of the area with the very same length as the obstacle ought to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844