Leading 10 usual forklift crashes ， forklift procedure need to take notice of these issues ！.

Do not take too lightly the forklift at the office. If the procedure is bad, there will certainly be significant accidents in minutes, and there are numerous mishaps including forklifts.

Situation 1: The forklift cargo blocked the chauffeur's sight, and the person in front could not be found, resulting in a rolling accident.
Case 2: In order to maintain the balance of the forklift when raising hefty items, the staff members utilized their body weight as the weight, which virtually created casualties.
Situation 3: The width of the forklift freight goes beyond the allowed size of the path and hangs on the roadside shelf, which virtually creates an crash.
Situation 4: Forklift is speeding and rolls over throughout a turn.
Situation 5: The forklift chauffeur did not discover the pedestrian, and the pedestrian did not notice the forklift.
Instance 6: The forklift raises the workers illegally, the forklift driver does not put on the seat belt, the forklift lifter falls and the vehicle driver is squashed when the forklift surrender.
Situation 7: The forklift driver did not put on a safety belt and fell from the lorry when it surrendered and was crushed.
Forklift procedure ought to take note of these matters ：.

Beginning.
1. Before starting, observe the surroundings, and after validating that there are no challenges that prevent the safety and security of driving, honk the horn first and afterwards start.
2. For vehicles with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge have to be risk-free prior to starting.
3. When the forklift begins with a tons, the driver must first verify that the load is steady and dependable.
4. The beginning should be slow-moving and stable.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground must be maintained 300mm-400mm, and the mast needs to be tilted backwards. .
2. Do not raise the fork too high when driving. When going into and leaving the job site or while driving, take care that there will be no challenges overhead. When the load is traveling, the fork needs to not be raised too expensive, which will certainly influence the stability of the forklift. .
3. After discharging, the fork needs to be lowered to the typical driving placement prior to driving. .
4. When turning, if there are pedestrians or automobiles close by, the driving signal should be provided first. High-speed doglegs are banned. High-speed sharp turns will trigger the automobile to shed lateral stability and tip over. .
5. When the forklift is downhill, it is strictly prohibited to switch off the fire and slide, and it is restricted to brake suddenly while driving with loads unless there are special scenarios.
6. When the forklift is running, it has to comply with the traffic rules in the factory and should keep a specific security range from the automobile ahead. .
7. When the forklift is running, the tons should remain in the most affordable setting that does not impede the driving, and the gantry must be appropriately slanted back. The tons will not be increased except when stacking or loading. .
8. The height of the load must not obstruct the vehicle driver's view. In unique scenarios, when the product impacts the forward vision, drive at a low speed when turning around.
9. It is restricted to activate the ramp, nor to drive across the ramp. .
10. The safe driving rate of the forklift in the manufacturing facility location is 5 km/h, and it should drive safely at a low rate when going into the production workshop area. .
11. When the forklift is raised, raised or driven, it is prohibited for personnel to stand on the fork to hold things and play a stabilizing function. .
12. If problems are located, they will certainly be repaired and reported in a timely fashion, and they will never run with health problems or conceal them.

loading and dumping.
1. When fork-loading products, the distance in between the two forks should be readjusted as needed to make the load of both forks balanced and not manipulated, and one side of the product should protest the rack. .
2. It is forbidden to deal with a single fork or make use of a fork top or pull. In unique situations, safety and security warning signs must be established to remind bordering pedestrians. .
3. In the process of loading and dumping products, the forklift has to be braked with the brake. .
4. The rate of the car need to be sluggish and steady. Beware not to roll the wheels on the dunnage, so as not to extend the rolled items and injure people. .
5. When making use of a fork to fork the goods, the fork ought to be as deep as feasible under the load, and it must be noted that the fork idea need to not touch other items or objects. The tons needs to be supported with marginal back tilt of the gantry so that the tons does not glide backwards. The mast can be slanted forward somewhat when the lots is lowered to enable very easy placement of the load and removal of the forks. .
6. It is restricted to fork goods at high speed and hit tough objects with the fork head. .
7. When the forklift is working, it is prohibited for individuals to stand around the fork, so as to prevent the collapse of the goods and injure individuals. .
8. Overloading is forbidden, and it is banned to use forks to lift personnel to engage in high-altitude operations to prevent high-altitude dropping crashes. .
9. It is not permitted to use the brake inertia to slip, put, round or roll objects. .
10. It is not enabled to utilize forks to choose, transform pallet dump.

Leaving .
1. It is restricted to leave the forklift when the items on the fork are in the air. Before leaving the forklift, you should discharge the goods or lower the fork framework.
2. Draw the emergency brake take care of to dead or dispirit the hand brake button.
3. The engine is switched off and the power is removed. (Except for unique conditions, such as the vehicle driver does not leave the lorry's view and does not go beyond 1 min).
4. Get rid of the secret. .

Forklift Operation Precautions.
1. Before and after the forklift operation, the appearance ought to be checked, and fuel, lubing oil and air conditioning water need to be included.
2. Inspect the security performance of starting, running and braking.
3. Examine whether the lights and horn signals are total and efficient.
4. During the operation of the forklift, examine whether the stress and temperature are normal.
5. After the forklift is running, the external leak must likewise be checked and the seals should be changed in time.

Forklift Safety Operation Specifications.
1. You need to check before leaving the car;.
2. When you run into somebody in front of you throughout driving, you ought to send a signal at a distance of 5 m;.
3. The driving rate in Electric Forklift Truck for Warehouse the factory does not exceed 5 km/h;.
4. When driving, the nadir of the cargo should be 0.3 m ~ 0.4 m in the air;.
5. The turning need to not be as well sharp to prevent the propensity of " complimentary turning";.
6. Adding and down the slope needs to be sluggish and uniform, and no activating the slope is permitted.
7. Do not drive across the slope. When the gradient is greater than 10%, the automobile should be driven in reverse when declining;.
8. When the forklift employees bring the goods and move on, if they come across large or hefty items and go to the vehicle driver's line of vision, they need to take the reversing workout
.
The "Eight Prohibitions" should be adhered to in the operation.
1. Single fork procedure is not allowed.
2. It is not Electric Forklift Truck for Warehouse enabled to raise the goods for long distance driving.
3. It is not enabled to grab the goods by handing over the pallet with the fork.
4. It is not permitted to directly shovel chemicals, flammables and various other unsafe chemicals with forks.
5. It is not allowed to utilize inertia pressure to pick up the goods.
6. It is not enabled to make use of braking force to expatriation round or easy-to-roll things.
7. It is not allowed to bring people to service the pallet or fork, and it is purely forbidden to stand under the fork after the fork is increased.
8. Do not drive side to side on inclines
.
Vehicle parking is not allowed under the list below problems.
1. Curves, narrow roadways, train crossings;.
2. Areas with a longitudinal slope higher than 5%.
3. When there is an obstacle on one side of the road, the opposite side of the section with the very same size as the barrier should be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844